The Tech 2 is the same tester GM Technicians use to diagnose GM vehicles. The Vetronix Tech 2 comes with Authentic GM software and provides support for on-board diagnostics on all GM systems 1992 thru 2014. But how to use the Vetronix Tech 2 Scanner ?

Please check the steps as following :

1. Turn on the power, the instrument enters the self-check state, and the screen performs “SYSTEM INITIANLIZING” for about 4 seconds; when the instrument emits a “beep”, the screen will display the version information of the instrument.
2. Press Enter to enter the main menu, the screen displays: F0-Diagnosis, F1- Service Program System, F2- Display Captured Data, F3- Tool Options, F4-Enable.
3. Use the up and down cursor keys to select the target and press the enter key to confirm.
4. Select the F0 function, enter the vehicle specification option, and select the model year by moving the cursor keys. Press the enter key to enter the vehicle system, select the appropriate type, and then press the enter key to enter the system selection menu, the screen displays: F0-engine power, F1-body, F2-chassis, F3-diagnostic circuit check.
5. Move the cursor keys to select F0 and press Enter to enter the engine type option. At this time, you can choose 3.2L V6G8 or 3.1L V6L82. Choose the former and press Enter to directly enter the following functions; select the latter and press Enter After pressing the car key, you must select BUICK and press Enter to enter the following functions. The screen displays: F0- fault code DTC., F1- data display, F2- special functions, F3- capture, F4-I/M information, F5 -ID information.
6. Select DTC and press Enter to enter the diagnostic code function: F0-DTC information, F1- failure record, F2- clear fault code, F3- capture information.
7. Move the cursor keys to select F0, press the Enter key to confirm, and enter the following interface: F0-DTC information, F1- view fault code special DTC., F2- clear fault code and record, F3- diagnosis test description.
8. Move the cursor keys to select F0, press the Enter key to confirm, and the fault code will be displayed. Use the cursor keys to turn pages; or press the corresponding key of INFO to provide relevant help information.
9. Return to “7”, select F1, press Enter to confirm, and enter the fault query interface. At this time, you can enter the fault code to query the referred fault and provide relevant help information.
10. Return to “6”, select F1 and press Enter to confirm. At this time, the fault code can be displayed.
11. Return to “6”, select F2, press Enter to confirm, the screen prompts: Do you really want to clear it? Y/N., press Y key to clear, press N key to cancel.
12. Return to “6”, select F3, press Enter to confirm, the screen displays: Recapture information, repeat display, and prompt whether you want to refresh Y/N., press Y to recapture, press N to repeat display.
13. Return to “5”, select F2, press Enter to confirm, the screen displays: engine, transmission.
14. Move the cursor keys to select “Engine”, press Enter to confirm, and enter the following operation interface: F0- Engine number? Net? F1- Catalyst data, F2-EGR valve data, F3- Oxygen sensor data, F4- Instrument data , F5- ignition data, F6- output driver data, F7- canister data.
15. Move the cursor keys to select F0 engine data, and press Enter to enter the following interface: engine speed, ideal idle speed, water temperature, intake air temperature, air flow sensor, engine load, etc. 58 items in total
16. Choose one of them to test.
17. Return to “5”, move the cursor keys to select F2 “Special Function”, press Enter to enter the following interface: engine output control, transmission output control, fuel system, idle speed control system, crankshaft position change learning function.
18. Select engine output control, press Enter, the screen displays: fan relay, fault indicator, air conditioning relay, carbon canister system, EGR solenoid valve, closed-loop data, cruise control, fuel pump, GENL — terminal.
19.You can enter the corresponding function by selecting.

Done!

More request for GM Scan Tools , welcome to check https://www.autonumen.com .

https://obd2software.info/2023/02/15/how-to-properly-operate-the-vetronix-tech-2-gm-scanner/

This article show a guide on how to configure a Volvo Vocom Interface to WLAN wireless mode using an access point.

Procedures:
Step 1: Connect VOCOM unit/cables to the PC and a Vehicle (key off).

Step 2: Click the “Settings” button.

Step 3: In the Settings menu click the “Configuration” button. The Configuration window will open. Select WLAN.

Step 4: To identify the configured communication unit. Enter a name of your choice and select OK. (ex. Garys_Adapter or VCforJA) NOTE: If you have more than one VOCOM, each will require a separate configuration and name.

If the connected device was already configured, a confirmation message will pop up asking if you want to load the configuration or set up a new configuration.
Step 5: Make a selection here for your configuration.

Step 6: Under Connection Type choose “Access Point”. To complete the configuration, the IT person will be required to enter the data. This is the data required for the VOCOM to connect to the Wireless Router.

Step 7: Click “Save” to complete configuration setup. NOTE: In the drop down there are 3 different Security Levels to choose from.

Example: This is an example of a completed configuration for the wireless router that we used. Your configuration will need to be set according to your location’s router. NOTE: The example used a different Security Level. Your configuration will vary depending on your network environment.

Step 8: Select the newly configured VOCOM WLAN (mode) Communication Unit. Click the “Activate” button and then “OK” to close the “Settings” window.

Step 9: Unplug The USB cable and the VOCOM will be in WLAN mode. NOTE: On the Product page you can see the VOCOM is now connected with the (WLAN). When the USB cable is plugged into the PC, the VOCOM will revert to USB mode.

Done!
If you need more about the latest Auto Scanner Tools , please visit our website : https://www.autonumen.com .

https://autodiagnostic.us/2023/02/11/how-to-configure-a-vocom-to-wlan-wireless-mode/

Alldata 10.53 plus Mitchell Ondemand 2 in 1 software now the latest version is 2014 alldata 10.53 and 2015 Mitchell Ondemand

First when you get the software, the following steps and notes for you to install it:

Step1: computer system requirment: windows XP or Windows 7 operate system.

Step2: Remove the antivious Program from your computer

Step3: open the alldata software from the HDD, then there is a video for you how to install the software step by step.

If you install the software and appear the below situation:

Then click ok to close, then will be ok.
Now the alldata and mitchell ondemand 2 in 1 are with best price.

Any more information about Automotive Diagnostic Software , please visit our website: https://www.autonumen.com .

https://autotool.us/2023/02/08/tips-for-installing-2014-alldata-10-53-2015-mitchell-ondemand-software/

Test feedback today: New Range Rover Sport P300 (L494) year 2018 successfully added the smart key with original JLR DoIP VCI Pathfinder interface. The real JLR DoiP VCI costs $1300 more. You might get a vxdiag JLR DoIP (less than $600 with HDD) that will do the same job.